Item # CC5238, Replacement Foot (Large for CC5225)
Factory Packaging 12/box br>
Minimum quantity is 12 br>
This is the foot for the Large end of the cargo bar. The foot pads are all the same size. br>
Whats in the box: 12 Replacement Feet br>
Item # CC5238, Replacement Foot (Small End for CC5225
Factory Packaging 12/box br>
Minimum quantity is 12 br>
This is the foot for the SMALL end of the cargo bar. The foot pads are all the same size. br>
Whats in the box: 12 Replacement Feet br>
Can be used in pickups, SUVs, vans and passenger cars. The soft rubber feet provide excellent grip and won’t mar surfaces.
Whats in the box: 4 SecureBarsâ„¢ br>
Series A Horizontal Track (Grey) Powder Coat. 10'
Made of high-strength steel br>
Steel constructed and tested for strength br>
Designed for Series E end fittings, beam sockets, and decking/shoring bars br>
10 ft. Galvanized F Track with 3/4" Hole.
1.62 in. hole spacing br>
Made of high-strength 15-gauge steel br>
Steel constructed and tested for strength br>
Designed for Series F end fittings and shoring bars br>
Standard Sliding W Track Winch
Steel components for reliable performance br>
Durable, salt spray-tested black powder coat finish for corrosion resistance  br>
Sliding configuration with compatibility with Wilson track  br>
Working load limit: 5,500 lbs br>
Steel Wheel Risers are used to raise odd-ball trailers up to dock height. The Steel Wheel Riser is equipped with fork slots for ease in fork truck transporting. Ramps may be stacked for compact storage when not in use. Fork pockets are 7-1/2" wide by 2-1/2" high usable. These fork pockets add approximately 15" to the overall width of the riser. Wheel Risers are designed to raise the trailer for loading and unloading to facilitate compliance with OSHA/ANSI B56.1 part 3 sec 7 requirements for maximum grade of ascending or descending loaded fork trucks. Made of heavy-duty welded steel construction. Uniform capacity per pair is 40,000 lbs. (Sold Each). (1/4" thick material).
Steel Wheel Risers are used to raise odd-ball trailers up to dock height. The Steel Wheel Riser is equipped with fork slots for ease in fork truck transporting. Ramps may be stacked for compact storage when not in use. Fork pockets are 7-1/2" wide by 2-1/2" high usable. These fork pockets add approximately 15" to the overall width of the riser. Wheel Risers are designed to raise the trailer for loading and unloading to facilitate compliance with OSHA/ANSI B56.1 part 3 sec 7 requirements for maximum grade of ascending or descending loaded fork trucks. Made of heavy-duty welded steel construction. Uniform capacity per pair is 40,000 lbs. (Sold Each). (1/4" thick material).
Winch Track-6' C-Track 6 ft. Long
High-quality steel for long-lasting performance br>
6-ft. length and 39 lb. weight  br>
Designed for standard sliding winches (43565-127 and 43565-157) br>
Bill of Lading BL005 can be personalized any way you want it. Personalize it with your logo. Has seperate "Bill To" section. Large area for comments or instructions. Plenty of space to add products to be shipped. Continuous Carbonless format.
Bill of Lading BL005 can be personalized any way you want it. Personalize it with your logo. Has seperate "Bill To" section. Large area for comments or instructions. Plenty of space to add products to be shipped. Snap A Part format.
This stretch wrap knife is safe and compact enough to fit into your pocket. Angled just right to easily slice through shrink wrap. Material is high density plastic.
The Topp-Clip is designed to defend against theft or breach of palletized cargo. The three point security system provides easy detection of pallet tampering.
Baked-in powder coated finish for added toughness. To install, insert loop at the tip of the fork and slide it up at a 45° angle. Then, lay the extension down over the fork.